Zoeller® 53-0001 Mighty-Mate M53 Automatic Effluent/Dewatering Submersible Pump, 43 gpm Flow Rate, 1-1/2 in Outlet, 1 ph, 3/10 hp, Cast Iron

16753001 MFG #: 53-0001
  • Brand: Zoeller®
  • Type: Automatic
  • Series: Mighty-Mate M53
  • Flow Rate: 43
  • Outlet Size: 1-1/2
  • Maximum Head: 19-1/4
  • Horsepower: 3/10
  • Voltage Rating: 115
  • Amperage Rating: 9.7
  • Frequency Rating: 60
  • Motor Speed: 1550
  • Cord Type: 3-Wire
  • Impeller Type: Non-Clogging Vortex
  • Temperature Rating: 130
  • Bearing Type: Sleeve
  • Material: Cast Iron
  • Dimensions: 10.0625 in H x 10.06 in W
  • Phase: 1
Zoeller® Effluent/Dewatering Submersible Pump, Automatic, Series: Mighty-Mate M53, 43 gpm, 1-1/2 in Outlet, 19-1/4 ft Maximum Head, 3/10 hp, 115 VAC, 9.7 A, 60 Hz Frequency, 1 ph ph, 1550 rpm Motor, 3-Wire Cord, Non-Clogging Vortex Impeller, 130 deg F, Sleeve Bearing, Cast Iron, 10.0625 in H x 10.06 in W Dimensions
  • Corrosion-resistant, powder coated epoxy finish
  • No sheet metal parts to rust or corrode
  • Stainless steel screws, switch arm, guard and handle
  • No screens to clog, watertight, neoprene square ring between motor and pump housing
  • Solid, buoyant, polypropylene float, oil filled, hermetically sealed, automatic reset ther
  • Upper and lower sleeve bearings running in bath of oil, Entire unit pressure-tested after
  • Watertight and dust tight, permanently oiled bearings
  • Cast iron switch case, motor and pump housing, engineered thermoplastic base, glass filled
  • Entire unit pressure-tested after assembly
  • Class B insulation, 7-1/4 in/3 in auto On/Off points
  • 1/2 in spherical solid handling, 9 ft cord, oil filled cooling
  • Cast iron cap, motor and pump housing, base, carbon and ceramic mechanical seals, engineer
  • AISI 1215 cold roll steel motor shaft
  • Single phase, shaded pole, 3 wire cord and plug
  • 1-1/2 in NPT discharge
Corrosion-resistant, powder coated epoxy finish
No sheet metal parts to rust or corrode
Stainless steel screws, switch arm, guard and handle
No screens to clog, watertight, neoprene square ring between motor and pump housing
Solid, buoyant, polypropylene float, oil filled, hermetically sealed, automatic reset thermal overload protected motor
Upper and lower sleeve bearings running in bath of oil, Entire unit pressure-tested after assembly, carbon and ceramic shaft seal
Watertight and dust tight, permanently oiled bearings
Cast iron switch case, motor and pump housing, engineered thermoplastic base, glass filled, plastic impeller with metal insert
Entire unit pressure-tested after assembly
Class B insulation, 7-1/4 in/3 in auto On/Off points
1/2 in spherical solid handling, 9 ft cord, oil filled cooling
Cast iron cap, motor and pump housing, base, carbon and ceramic mechanical seals, engineered plastic impeller, stainless steel hardware, neoprene gasket
AISI 1215 cold roll steel motor shaft
Single phase, shaded pole, 3 wire cord and plug
1-1/2 in NPT discharge